Useful tips 

Oil volume Toyota Camry 2.5 v50. Recommended engine oil for Toyota Camry. Engine oil for Toyota Camry

The Toyota Camry business class car is quite reliable and unpretentious, but at the same time, it requires qualified service. Fortunately, this applies to cases with serious breakdowns that only engineers can handle using special diagnostic stands, equipment, etc. As for smaller procedures, such as changing engine oil, they can be done at home. And indeed, as practice shows, even an inexperienced motorist can cope with changing the engine oil. But there is one more task, without which the oil change process is not possible. We are talking about the choice of lubricant, and everything that goes with it. So, using the Toyota Camry as an example, we will consider in detail how to choose the right engine oil and how much to fill it.

How often do you change the oil?

Toyota has developed an oil change schedule for the Camry, which is 20 thousand kilometers. But in some cases this figure can be adjusted downwards - for example, when operating in harsh climatic conditions. In this case, the replacement frequency will have to be reduced to 10-12 thousand kilometers. Thanks to this, the oil will not have time to become unusable, and the engine will last much longer.

In what cases is it necessary to urgently change the oil?

Let us highlight several main factors and signs by which you can judge the condition of the engine oil:

  • The oil has become unusable if it contains dirt deposits, soot, dirt and metal shavings
  • The oil has become unusable if it smells burnt and has a dark brown tint.
  • The gearbox is unstable, there may be delays when changing to the next speed
  • Increased fuel consumption
  • When you press the gas to the floor, the engine does not develop maximum speed
  • Noises and vibrations in the transmission and engine, shaking is transmitted to the steering wheel
  • The general perception of driving a car changes for the better and for the worse.
  • Unpredictable frequency of gearbox and internal combustion engine breakdowns
  • Increased oil consumption

How to choose oil and how much to fill it in

The Toyota manufacturer advises filling only original oil into the Camry engine, but in fact you can save money by using an alternative product. So, today we can already admit that the chemical industry has developed enough to not doubt the analogue oil. But at the same time, you should choose only from proven brands with a good reputation, of which there are quite a few. So, from them we can highlight Castrol, Mobile, ZIK, Lukoil, G-Energy, Kixx and others.

Since even when choosing an analogue oil, one should proceed from the parameters of the original product, in the future we will take them into account. Next, we will consider what kind of oil to fill and how much it is needed depending on the displacement of the Toyota Camry engine.

For engines 1AZ-FE and 2AR-FE (2.0 and 2.5 l respectively)

For these engines, the best oil is Energy Conserving with a recommended SAE viscosity of 0W-20, 5W-20, 5W-30 or 10W-30. It is advisable to buy universal oil. It is suitable for almost any weather conditions.
According to the API standard, universal motor oils of categories SL, SM and SN are suitable.

In terms of oil volume, a 2-liter engine requires 4.3 liters, and a 2.5-liter engine requires about 4.3 liters of fluid. If you do not take into account the oil filter, the volume is 4.1 and 4.0 liters, respectively.

For 2GR-FE 3.5 l engines

For 6-cylinder engines, Energy Conserving oil or universal ILSAC oil with viscosity parameters 5W-30 and 10W-30 are suitable.

  • Suitable API parameters for the 3.5-liter engine are SL, SM and SN.
  • The volume of oil to be filled, including the oil filter, is 6.1 liters, without it – 5.7 liters.

What is 15W-40

As an example, we will give an oil with the indicated designation. In this case, the number 15 and the letter W indicate the characteristics of the oil at low temperatures. The smaller the number preceding the letter W, the more efficiently and quickly the engine starts in cold weather. In this case, this oil is better suited for warm weather.

The next number - 40 - indicates viscosity at high temperatures. The higher this figure, the better the oil is suitable for high speeds or operation with maximum load.

It can be concluded that for warmer weather conditions, an oil with SAE 10W-30 parameters may be preferred, and for harsher climates, SAE 0W-20 or 5W-20 would be ideal.

Types of oils

Finally, let’s look at the three most popular types of motor oils.

  • Synthetic is a modern oil that is resistant to low temperatures. It has a high degree of fluidity, and due to this it never freezes in frosty weather. This fact allows you to use the oil not only in summer, but also in winter. Recommended for modern cars with low mileage. Ideal for Toyota Camry.
  • Mineral is the worst of all existing oils. It has a low degree of fluidity and is therefore suitable for older cars with a high risk of oil leaks. Due to its excessive thickness, “mineral water” will never flow out even through a microcrack. Perhaps this is the only advantage of mineral oil, along with its low price.
  • Semi-synthetic - includes a mixture of synthetic and mineral oils. It is suitable as a replacement for the mineral composition, as it is superior to it in many ways. This is a more modern and high-quality product. It can be recommended for modern cars with low mileage.
    So, for Toyota Camry it is best to choose synthetic oil, and semi-synthetic oil takes second place.

Among the best brands of motor oils, we note Lukoil, Castrol, ZIK, Mobile, Elf, G-Energy and others.

Toyota Camry is a popular middle and business class car almost all over the world, which is affordable for many adherents of true Japanese quality. Cars from this model line have a long service life and often last up to a mileage of 1 million km. To prevent premature breakdowns and extend the period of effective operation of the car, you should adhere to the maintenance schedule and undergo repair work before breakdowns become serious.

Changing automatic transmission oil Toyota Camry 2.5

The automatic gearshift transmission on the Toyota Camry creates almost all the conditions for comfortable driving. A mechanism of this type does not distract the driver’s attention from the road by switching lever positions and independently selects the optimal speed.

The Toyota Camry 2.5 automatic transmission oil is changed every time the odometer reaches 90 thousand km. During this period of operation, ATP fluid almost completely loses its working properties and does not prevent overheating of transmission parts.

It is strictly not recommended by the car manufacturer to service the Toyota Camry automatic transmission yourself. Errors made during the maintenance process can negatively affect the functionality of the transmission and even cause it to fail. Automatic transmission repair on a car of this model is expensive, difficult to perform and labor-intensive work. Therefore, you will have to spend a lot of money, effort and nerves to restore the machine’s functionality.

Oil change in Toyota V50 at the Autopilot technical center

Maintenance of the Toyota Camry power unit must be carried out much more often than the automatic transmission. Engine oil loses performance characteristics after a mileage of 10-15 thousand km. If the vehicle is not used intensively, the service should be performed once a year.

In Moscow, you can replace the Toyota Camry engine lubricant, as well as other consumables, at a competitive price at the Autopilot technical center. By contacting us, you will provide yourself with such advantages as:

  • high quality car service provided by experienced and qualified professionals;
  • guarantee for all services of masters;
  • affordable pricing policy for motorists.

Do you need an oil change for Toyota Camry 2.5 V50 in Moscow? Visit the Autopilot technical center!

Oil change Toyota Camry

The oil in the engine is an important element that directly affects the functioning of the unit. Without its timely replacement, the car will fail, and repairs will be expensive and difficult. Toyota Camry The V50, like other cars in this series, needs high-quality motor oil, the effect of which is clearly noticeable on engine performance. Lukoil oil is perfect

What fluid does the engine require?

What kind of oil to pour into a Camry is a rather pressing question. The manufacturer produces not only cars, but also adds to this list. When purchasing branded products, of course, do not worry about the comparability of the product, but the original cannot be purchased from every individual. Camry makes good use of synthetic oils with viscosities of 5W-30 and 5W-40.

Read also

Toyota Genuine Motor Oil is a unique product; Which oil is better among analogues is worth thinking about. There are many brands, but it is better to pour products into Camry from proven manufacturers who guarantee the highest level of quality of the product. They use Lukoil motor oil with a viscosity of 5W40, unfortunately it will have to be changed more often than industrial oil. Camry V40 3.2.4 produced in 2007 runs on the unique Toyota 5W30 SM or SL. On the Russian market, the 1st option is more common, the 2nd is usually offered as non-original, therefore it is not recommended to contact a child.

Reasons for increased oil consumption

If the engine consumes a certain amount of consumable water during operation, if it is in good condition, the indicator is so low and practically unnoticeable, but the engine has begun to consume a lot, which means that the Camry model is experiencing certain difficulties. Excessive consumption does not occur by chance: it is recommended to diagnose the unit; lost time can cause a breakdown, the correction of which requires serious financial costs.

During engine operation, not all the oil is removed by oil scraper rings and sent to the sump. A small part of it burns out: for example, for Camry V40 2.4.4 2007 produced by another similar car with an engine capacity of 3.5.5 liters. natural consumption is 0.05% - 0.25% of the total amount of water.

Read also

Consumption on a new engine is practically not noticeable, on used cars, for example, 2007 and older, This process is more pressing, because natural wear and tear occurs, which is why the appetite of the unit increases greatly. If you make frequent changes in the engine, and at the same time you have to pour more water with enviable consistency, this means that it is necessary to find the fault. You will like her more with an ordinary, or in other words, complex character. The main reasons for complex defects are as follows:

Toyota Camry XV50 Toyota Camry 2.5 2013 Oil and filter change

How much oil is in the Camry 2.5 engine.

oil filter 04152-31090 air filter 17801-28030 cabin filter 87139-50100 oil motor 5w30 5l.

  1. wear of piston rings. It occurs due to friction of parts. If the rings are worn, a gap will appear through which oil will escape through the Camry V40 2.4 exhaust system. If the motor has been overheated, the rings may be stuck. You can see this, of course, by the exhaust, which has acquired a blue color;
  2. The walls of the cylinders also wear out during the use of the car. There is an option to bore these elements to a certain size or change the block completely. Option 1 is a little cheaper;
  3. It happens that the Camry V40 2.7.4 eats oil due to a problem with the valve stem seals. These are oil seals that come in variations and lose their elasticity. Changing them is quite difficult at a technical level, but relatively cheap. Complete disassembly of the car engine is not necessary;
  4. on 2007 Camry There is a widespread problem with the release when oil drips from under the cylinder head gasket. There is a discrepancy due to the age of the car. New Camrys usually do not suffer from this problem, but it is recommended to continue checking the tightness of the bolts. If the car is old, it is recommended to change the gasket. Over time it burns out;

How to change it yourself?

Substitution oils Toyota Camry is required approximately once every 10 thousand kilometers. These are reasonable times, where a lot of dirt does not have time to accumulate, here the liquid settles down enough to be used up. If you use a brand name, of course, postpone the replacement for thousands of kilometers; if Lukoil, it is better not to deviate too much.

If you wish, you can change the engine oil in your garage. For this purpose, you need to be well prepared, have the necessary tools, filters and gaskets, as well as a container for waste water.

Read also

Clear quantity oils required for replacement is indicated in the service book. If it is not there, you will need 4.4 - 4.3 liters for the engine, 4.4 liters for the 2.7.5 engine.

Changing the engine oil is done according to the following scheme:

  1. The car is placed over the pit, in other words, driven onto the overpass. The engine needs to be warmed up beforehand;
  2. after a while, it is necessary to remove the crankcase protection element, unscrew the drain plug, the oil will drain into a substitute bucket. This will take about a quarter of an hour;
  3. then you need to change the filter, tighten the drain plug, putting it back;
  4. refilling of the new one occurs through the cap located on the engine, it is under the hood;
  5. check the water level, start the car, wait about a minute until the engine shows that it is working correctly, and turn it off again;
  6. At the very end we check the oil again. We do this when the engine has cooled down; if the level is insufficient, you need to top it up. If there is a lot of water, there is an option to leave it as it happens, the car itself will squeeze out the excess.

Changing the engine oil is an important event in the life of every vehicle. Motor oil performs several important tasks, including:

  • Protection of the engine from overheating, as well as its components from accelerated wear.
  • Prevention of corrosion.
  • Removing from working areas such engine work products as metal shavings, soot, carbon deposits, etc.

Depending on the type of oil, it may contain various additives.
They promote self-cleaning of the engine while controlling oil viscosity.

Many motorists are interested in when the oil in a Toyota Camry engine should be changed. This working fluid oxidizes over time and, accordingly, loses its positive properties. Each driver can find the frequency of oil changes in the technical manual for their car. It is worth noting that this figure varies for European and CIS countries, so be sure to find the relevant data in the documentation for the car.

If for some reason you were unable to find this information, then it would be optimal to change the oil on Toyota Camry v40 and v50 every 10 thousand kilometers. You can reach 15 thousand, but this is a last resort. It should be borne in mind that this indicator is also influenced by several parameters such as:

  • Features of car operation (aggressive or calm driving style, frequent stay in traffic jams).
  • The quality of the fuel used.
  • Age of the vehicle.
  • Climatic conditions (in hot weather the oil life is reduced).

In some cases you will need to replace more frequently. Oil wear can also be determined visually. It is necessary to warm up the car to operating temperature, and then take a small amount of oil with a pipette, and then drop it onto regular or filter paper. When it is absorbed, you will see a small spot that consists of an outer and inner circle. If the outer circle is sufficiently blurred and has a light tint, then the oil is in good condition. If the outline of the outer circle is clearly visible and the color of the mark is close to the color of burning, it is recommended to replace it.

What happens if you don’t change the oil in a timely manner?

Driving on used oil carries with it several dangers, in particular:

  • Possible engine overheating. Old oil dissipates heat much worse.
  • Increased friction between moving engine components, resulting in accelerated wear.
  • Reduced anti-corrosion protection.
  • Accumulation of fuel combustion products inside the engine, which eventually clog the oil channels.

All this, at best, will lead to increased fuel consumption, and at worst, to a major engine overhaul.

Engine oil for Toyota Camry

Once you have figured out how often you need to fill in new oil, another question arises - what kind of oil to fill in the Toyota Camry. You can also find the answer in the technical manual for your foreign car. Oil from the car manufacturer guarantees maximum service life and safety for the engine. It is recommended to use original Toyota oils 0W20, 5W30 or 5W40.

The only drawback of such products is the fairly high cost. The market offers a wide selection of analogues. Products from Mobil 1, G-Energy, Valvoline, and Lukoil will be a good purchase. When purchasing, be sure to pay attention to the viscosity parameter. For gasoline and diesel engines, it is necessary to select the appropriate oil.

The manufacturer recommends using synthetic or semi-synthetic products. It provides better engine protection under loads and low temperatures, leaves virtually no residue on the walls of the unit, and generally extends the life of the engine. Also, synthetic oils have less volatility than mineral oils.

How to change oil on a Toyota Camry

Before making a replacement, you need to not only buy new oil, but also an oil filter. It is needed to cleanse the oil of soot and other harmful impurities. Replacing the Toyota Camry oil filter should be done along with changing the oil. On the market you can find both original and compatible parts from third-party manufacturers.

Changing the oil in a Toyota Camry includes the following steps:


Finally, start the car. Make sure there are no leaks anywhere. Now you can change the oil yourself and save money on car service. The procedure is not difficult and will take you no more than 20 minutes.

Car manufacturers pay great attention to consumables; the operating instructions indicate all the necessary lubrication parameters. Car enthusiasts, when choosing oils for summer or winter, must take into account the requirements of car manufacturers, otherwise the engine may quickly fail. We invite you to familiarize yourself with the parameters of the recommended engine oil for Toyota Camry.

1994 model

The Toyota Camry automaker insists on using universal lubricants of the SG or SG/CD class according to the API system. To select the viscosity, you must use scheme 1.

Scheme 1. Predicted range of temperatures outside the car until the next oil change.

In accordance with scheme 1, when the thermometer reading is above -23.5 0 It is recommended to fill with liquids 10w-30, 10w-40, 10w-50. If the thermometer reading is above -12.5 0 C, then it’s worth pouring 20w-40, 1-20w-50. At temperatures below +10 0 You need to use 5w-30 fluid.

Refill tanks including the oil filter are:

  • 3.8 l for 5S-FE auto engines;
  • 4.5 l if the engine is 3VZ-FE;
  • 5.0 l corresponds to 1MZ-FE car engines.

Toyota Camry XV20 1996-2001

1998 model
  • for 1MZ-FE motors, SH class lubricant according to API standards;
  • for 5S-FE car engines, motor fluids of group SG and higher; in the absence of woven motor oil, it is permissible to pour class SF.

To select the viscosity parameters of the lubricant, Scheme 2 is used.

Scheme 2 Predicted temperature range outside the car until the next oil change.

In accordance with scheme 2 at a temperature range above -18 0 It is necessary to use lubricants 15w-40 or 1-20w-50. If the thermometer is below +10 0 C, use 5w-30 motor oils.

Refill containers:

  1. Auto engines 1MZ-FE:
  • 5.5 l dry engine;
  • 7 l with oil filter change.
  1. Motors 5S-FE:
  • 4.3 L dry engine;
  • 3.6 l with oil filter change.

Toyota Camry XV30 2001-2006

2005 model
  1. According to the API system, groups SJ or SL, having a viscosity of 20w-50 or 15w-40, are used at air temperatures above -12.5 0 C (see diagram 3).
  2. In accordance with the API classification, classes SJ or SL, designated “Energy Conserving” or universal motor oils certified according to ILSAC. The applied viscosity of such lubricants is 10w-30 at temperatures above -18 0 C, or 5w-30 if the air temperature is below +10 0 C. When choosing a viscosity indicator, take into account diagram 3.
Diagram 3. Estimated temperature range before the next oil change.

The amount of lubricant that will be needed during subsequent replacement is:

  • 3.8 l with an oil filter or 3.6 l without an oil filter for 1AZ-FE engines;
  • 4.3 l including filter or 4.1 l without oil filter for 2AZ-FE engines;
  • 4.7 l with an oil filter or 4.5 l without an oil filter in the case of 1MZ-FE engines.

The approximate volume of lubricant that needs to be added so that the lubricant level is between the lower and upper level marks on the Toyota Camry dipstick is:

  • 1.0 l for 1AZ-FE engines;
  • 1.5 l in the case of power units 2AZ-FE and 1MZ-FE.

Toyota Camry XV40 2006-2011

2008 release
  1. All-season motor fluids with the designation “Toyota Genuine Motor Oil” or motor oils with similar parameters, having the appropriate markings or approvals on the canister.
  2. According to API standards, acceptable lubricant classes are SL or SM. Viscosity parameter according to the SAE system 20w-50 or 15w-40 at a temperature above -12.5 0 C (temperature selected according to scheme 4).
  3. In accordance with the API classification, types of motor oils are SL or SM, designated “Energy Conserving” (energy-saving) or all-season lubricants according to ILSAC. Viscosity is selected 10w-30 when the thermometer reading is above -18 0 C, or 5w-30 if the air temperature is below +10 0 C (temperature indicators are taken from diagram 4).
Scheme 4. Dependence of the viscosity index of motor oil on the temperature of the region in which the car will be operated.

Refill tanks for Toyota Camry:

  1. Engine 2AZ-FE:
  • 4.3 l with oil filter;
  • 4.1 l excluding oil filter.
  1. Auto engine 2GR-FE:
  • 6.1 l with oil filter;
  • 5.7 l without oil filter.

Toyota Camry XV50 since 2011

2013 model

According to the operating instructions, the lubricant for Toyota Camry engines is original Toyota oil or lubricants from other companies that have the parameters required by the car manufacturer. The class, type and viscosity of the oil are determined by the type of engine.

Power units 6AR-FSE and 2AR-FE

According to the manual, it is necessary to fill in oils with a viscosity index of 0w-20, 5w-20, 5w-30 or 10w-30, corresponding to classes SL or SM with the designation “Energy Conserving” according to the API system. It is acceptable to use universal lubricants certified according to ILSAC and having a viscosity parameter of 15w-40. You can also use motor oils of groups SL, SN or SM according to the API system.

To select the viscosity depending on the temperature outside the car, use diagram 5.

Scheme 5. The influence of air temperature on the selection of motor oil viscosity.

According to scheme 5, at extremely low temperatures it is necessary to fill in lubricants 0w-20, 5w-20, 5w-30. Motor oils with a viscosity parameter of 10w-30 or 15w-40 should be used if the thermometer is above -18 0 Otherwise, starting the engine will be difficult.

The volume of engine oil required during replacement is 4.4 liters including the oil filter and 4.0 liters without replacing the oil filter.

Auto engines 2GR-FE

  • SL or SM with the designation “Energy Conserving” (energy saving);
  • SN marked “Resource-Conserving” (resource-saving).

You can also pour lubricants certified by ILSAC and having a viscosity parameter of 15w-40 or use oil groups SL, SM and SN with the recommended viscosity index.

You can select the viscosity parameter according to scheme 6.

Diagram 6. Predicted temperature range until the next engine fluid change.

According to scheme 6, at extremely low temperatures it is necessary to use 5w-30 lubricants, and when the thermometer reading is above -18 0 C, pour 10w-30 or 15w-40.

The volume of engine fluid required when replacing is 6.1 liters with oil filter replacement and 5.7 liters excluding the oil filter.

Conclusion

By using the recommended engine oil for Toyota Camry, you can increase the life of the engine and lubrication system. The fact is that the lubricant creates a protective film on the surface of the internal elements of the car engine, the properties of which depend on the quality parameters of the lubricant. The thicker the car oil, the thicker the protective film will be; such oils should be used in the summer; thinner lubricants are used in winter; they ensure cold starting of the engine. If you use an oil that does not match the parameters, the film may break and the engine will start to run “dry” - this will lead to its breakdown.

When replacing lubricant, consider:

  • the manual indicates the reference volume of oil that will be needed when changing the lubricant; in real conditions it may differ slightly;
  • Overfilling the vehicle oil above the maximum mark on the dipstick is unacceptable, therefore, after adding lubricant, it is necessary to check the lubricant level.

Watch a video on how to change the oil in a Toyota Camry with your own hands:

Recommended engine oil for Toyota Avensis