Car alarms. Tips for installing and configuring car alarms Pandora 3500 connection diagram
Central block
Pandora DXL 3500
Security system Pandora DXL 3500 This is a device from the company's lineup Pandora, which began updating its products in 2012. Meeting all modern requirements for reliable vehicle protection, Pandora DXL 3500 is a progressive two-way interactive security system of the highest class.
The integrated CAN module supports more than 300 vehicles equipped with the appropriate bus. There is also a LIN port, which simplifies the integration of the system into some brands of cars.
The system is equipped with a sensitive three-axis accelerometer that records vehicle tilt, impacts, collisions and temperature conditions. Architecture Pandora DXL 3500 is designed in such a way that you can connect a large number of additional devices, for example: GSM/GPRS module, immobilizer, GPS module, etc.
Signaling Pandora DXL 3500 features amazingly low power consumption - only 18 mA, which is one and a half times lower than in the previous model -.
High reliability of the product is confirmed by a guarantee 3 years from the manufacturer. It is important to note that the entire production process and all components were manufactured in Russia, Kaluga, at the Experimental Instrument Making Plant.
CAN interface
The CAN protocol is installed on more than 300 models of modern cars. It speeds up the integration of the system into the vehicle's electronics and also allows, if desired, to control many vehicle parameters.
Three-axis accelerometer
A sensitive motion sensor reacts to collisions and records the force and direction of the impact, recording the event in the system's memory. It also responds to tilts (for example, during an evacuation). A temperature sensor is also available.
USB connector
On the central block Pandora DXL 3500 available mini-USB connector With its help, you can connect a personal computer to the system. This will allow you to manage alarm functions, update CAN protocols and keep records of system operation.
Two-way conversational encryption
Innovative technologies of Russian engineers based on military developments made it possible to increase the protective properties of the system to the maximum. Conversational encryption with intelligent cryptographic security eliminates the possibility of electronic hacking Pandora DXL 3500.
Functional Features
Pandora DXL 3500 cable kit
- Control block Pandora DXL 3500.
- Keychain with LCD display, double-sided.
- Additional keychain.
- RF module (radio module).
- Thermal sensors for monitoring interior and engine temperatures.
- "Valet" button and LED indicator, with wires.
- Installation kit.
- Five-channel autostart relay module.
- Plastic card with an individual PIN code.
“Instructions for PANDORA DXL 3500 System operation General information System features Remote control key fobs System functions Protected...”
Instructions for PANDORA DXL 3500
System Operation
general information
System Features
Remote control key fobs
System functions
Protected areas of the car
Introduction
System components
Keychain with LCD display
Replacing the battery in the key fob
Keychain ringtones
Purpose of key fob indicator lights
Key fob functions
Preparing the key fob for use
general information
Silent mode of operation of the key fob
Checking the number of key fobs registered in the system
Purpose of icons on the display Functions quickly called up by buttons Security and service functions of the system Opening the trunk lock Disarming the system Arming the system Setting up an alert when leaving the reception area Operating the system in security mode Operating the system in security mode Locking/unlocking doors Locking/unlocking doors Automatic arming control System status monitoring Viewing event history 1/53 manuals.alarmtrade.ru Remote control of sensors Vehicle search Panic mode
Timed channels Driver call Maintenance mode Arming with the key in the ignition Additional functions Light alarm and siren sound signals Emergency system control Immobilizer functions HANDS-FREE mode
ANTI-HI-JACK mode
Automatic and remote engine control Remote and automatic engine starting, general information “Program neutral” procedure
Remote engine start Automatic engine start Ignition support mode
Three-color system status indicator (“LED”) System Operation General Information System Features
Double-sided key fob with liquid crystal display:
Switching the security mode on and off using different buttons.
Monitoring the status of 11 independent security zones.
Vibration alert built into the keychain.
16 sound alert melodies.
Automatic fluorescent backlight of the LCD display.
Confirmation of button presses with a vibration alarm.
Key fob battery AAA (1.5V), up to 6 months. continuous operation.
Indication of battery discharge level.
2/53 manuals.alarmtrade.ru
Synchronization of the key fob and base unit clocks, the exact time in the event history.
Indication of engine temperature and interior temperature, battery voltage.
Quick remote adjustment of the sensitivity of the built-in shock sensor.
Quick remote adjustment of the sensitivity of the built-in motion sensor.
The communication range with the processor unit is over 1800 m in the field of view.
View the 10 most recent events by time and event.
Automatic control of the radio coverage area of the notification channel.
Base unit
Conversational coding of commands.
Personal encryption key 128-bit long, can be changed by the user.
Separate individual PIN code for disarming the system.
Maintaining a log of events in the base unit with recording of the event and the exact time during the period of lack of communication with the key fob with LCD for subsequent transmission to the key fob.
Possibility of using single-wire digital blocking relay BM-103/105.
Possibility of connecting “Touch Memory (TM)” or “iButton” keys to organize additional locks and control service modes of the system.
Built-in integral accelerometer for motion and shock recognition with adaptive processing algorithms and sensitivity adjustment from the key fob.
Separate hood and trunk sensor inputs.
An improved method for polling sensors that eliminates false alarms.
High-precision measurement of engine and interior temperatures, indication on the key fob display.
Intelligent function "Ignition support"
Intelligent "Turbo timer" mode for cooling the turbine of cars equipped with it.
Remote starting and warming up of the engine upon command from the key fob.
Automatic start according to the daily timer.
Automatic engine start/stop based on engine temperature.
Automatic cyclic engine start to warm up at time intervals.
Automatic engine start based on voltage (to recharge the battery)
Two-step door unlocking.
Security mode with engine running.
Automatic arming.
Taking into account the delay of interior lighting when arming.
Possibility of implementing the “Hands-Free” mode for arming/disarming without using a key fob (Pandect IS-471/477/577/590/600 immobilizer is required).
System software update from the manufacturer's website via the built-in mini-USB port.
Remote control key fobs A two-sided key fob is the main means of controlling and monitoring the state of the system. To facilitate the perception of events, the key fob uses 16 melodies. Each melody corresponds to a separate event.
3/53 manuals.alarmtrade.ru The key fob uses flashing LED indicators that increase the information content of the key fob. If “green” is flashing, then there is a connection, there were no alarm events; if “red”, then either an alarm notification has been received, or communication with the main unit has been lost, or the car is not armed.
A two-way key fob is the main means of managing and monitoring the state of the system.
Purpose of the key fob indicator lights:
The “SEND” indicator is green.
If there is communication in the notification channel, it flashes briefly.
q When there is no connection at all, it does not light up.
q The ALARM indicator is red.
It flashes frequently during any alerts.
q After the end of any alarm, until any button is pressed q, it flashes briefly and additionally, once a minute, a short sound signal is heard.
If there is a complete lack of communication, it flashes briefly.
q System functions High security dialogue code.
q Personal encryption key 128-bit long for each product, it can be q replaced by the user.
Highly confidential system PIN code (four digits) for changing system parameters.
Separate individual PIN code for disarming the system (under the protective layer q on the card) Keeping a log of events in the base unit with recording of the event and the exact time during the q period of no communication with the LCD key fob for subsequent transmission to the key fob.
– – –
BM103/105(M,D,W).
Possibility of connecting “Touch Memory (TM)” or “iButton” keys to organize q additional locks and control the service modes of the system.
Built-in integral accelerometer for motion and shock recognition with q adaptive processing algorithms and sensitivity adjustment from the key fob.
On-board network voltage monitoring.
q Monitoring the state of the vehicle’s standard security system* q Separate sensor inputs for the hood and trunk with the ability to change polarity.
q Improved method of polling sensors, eliminating false alarms.
q Possibility of highly accurate measurement of engine or interior temperature with q subsequent indication on the key fob display.
Intelligent function “Ignition support”.
q Intelligent “Turbo timer” mode for cooling the turbine of cars equipped with it.
Possibility of remote starting and warming up of the engine upon command from the key fob q Possibility of automatic engine start using a daily timer q Possibility of automatic engine start/stop based on engine temperature q Possibility of automatic cyclic engine start for warming up after q time intervals Possibility of automatic engine start based on voltage (for recharging q battery) Warnings about the imminent stop of an automatically and remotely started q engine, the ability to quickly change the warm-up time from the key fob 12 timer channels with a flexible algorithm for setting up and turning off according to q system events.
Possibility of flexible organization of blocking using timer channels of both NC and q and NO relay contacts.
Two-step door unlocking.
q Security mode with the engine running.
q Automatic arming.
q “Driver Call” function q Taking into account the delay of interior lighting when arming.
q Possibility of implementing the “Hands-Free” mode for arming/disarming without q using a key fob (Pandect IS-477/577/590/600 immobilizer is required).
Possibility of programming system settings via a personal computer (USB cable required) Possibility of programming up to four key fobs.
q *Availability of this feature may vary depending on your vehicle make and model.
Protected zones of the car The Pandora DXL3500 car security system protects the following independent zones with the issuance of a corresponding notification on the key fob and recording in the synchronous event protocol of the base unit:
– – –
hood limit switches q trunk limit switches q turning on the ignition q pressing the brake pedal q activation of the built-in shock sensor (preliminary level) q activation of the built-in shock sensor (alarm level) q operation of the built-in motion sensor q operation of an additional two-level sensor (preliminary level) q operation of an additional two-level sensor sensor (alarm level) q critical drop in the supply voltage of the vehicle’s on-board network (disconnection q of the battery) reminder of the side lights not being turned off when arming* q state of the standard security system* q All alarm events are recorded in the system’s non-volatile memory (even if the system’s power is instantly turned off disabled) with recording of the exact time of the event. This allows you to display the history of events on the car alarm key fob after any time has passed without communication between the base unit and the key fob.
*Availability of this feature may vary depending on vehicle make and model.
Introduction Thank you for purchasing the Pandora DXL3500 car security alarm system - a premium security and service device designed for installation on modern B-C-D-M-S class cars equipped with digital data exchange buses (CAN). Pandora DXL 3500 was developed and produced in Russia by the Experimental Instrument Making Plant (Kaluga), which is the copyright holder of the Pandora trademark in the Russian Federation (certificate No. 408051, 408052).
6/53 manuals.alarmtrade.ru This product is the result of the work of a group of highly qualified Russian engineers, using many unique engineering and technological solutions.
The product is made on a modern element base using new technological equipment from world leaders, which guarantees high quality, reliability and stability of technical and user characteristics.
Pandora DXL 3500 has the most secure command authorization code with a unique dialogue algorithm and an individual encryption key for each product (at least 128 bits). "Experimental Instrument Making Plant" guarantees users of this system complete protection against electronic hacking throughout the entire life of the product.
By installing this car alarm, you can count on a three-year unconditional manufacturer’s warranty; service support in most cities of Russia and neighboring countries; prompt assistance in resolving emerging issues related to the operation and installation of the system, provided by an online support service and a toll-free hotline.
The Pandora DXL 3500 security alarm system supports the ability to update software via the Internet from the manufacturer’s website. The software can be updated by connecting a personal computer with Internet access to the mini-USB connector built into the base unit.
Pandora DXL 3500 is designed for installation on a vehicle and is connected to standard wiring with a voltage of +12V and the common negative terminal of the battery connected to ground. The system can be installed on cars with both a manual and automatic transmission, with a diesel or petrol, carburetor or injection engine, as well as on cars with a hybrid power plant. The system is installed on cars with a traditional ignition switch and cars equipped with a SmartEntry or Keyless system (with a “START” button).
The warning range in open areas can reach several kilometers.
The security system modes in urban environments can be controlled at a distance of 300-650 m.
The use of effective energy-saving modes in the system using components from microelectronics market leaders (microcontrollers from MicrochipTechnology Inc., USA, integrated transceivers from Silicon Labs Inc., USA) made it possible to significantly reduce the energy consumption of the key fob, increase the communication range and noise immunity of the radio channel. In the base unit of the system, for the first time for two-way security and car service systems, a new 32-bit microcontroller of ARM architecture is used, providing the highest performance in processing signals from high-speed digital buses of modern cars, intelligent processing of the built-in highly sensitive three-coordinate accelerometer, on which multiple security systems are implemented and service functions of the system.
The system has a climatic modification U-2.1 (N-2.1) in accordance with GOST 15150-69 and is designed for operation at ambient temperatures from -40°C to +85° 7/53 manuals.alarmtrade.ru C. All components of the security system included in the kit are should only be installed inside the vehicle. LCD key fobs of the security system are designed to operate at temperatures from -10°C to +40°C.
Protection of the base unit and security system key fobs from water ingress - category IP40 according to GOST 14254-96. The system was developed and manufactured in compliance with the requirements of GOST R 41.97-99 (UNECE No. 97), GOST R 50789-95, GOST R 28279-89, GOST 28751-90 (ST SEV 6895-89), GOST 29157-91, GOST R 50607-93.
Our Internet address: www.alarmtrade.ru User support service: [email protected] Hotline phone number: 8-800-700-17-18 (calls within Russia are free) Made in Russia, Kaluga, st. Kirova 20A.
System components
1. Base unit
2. RF module with cable
3. Main remote control with LCD display
4. Leather case for LCD key fob
5. Additional remote control key fob (three-button)
6. Main cable.………….………………………………………………………………………………...……....1 pc.
7. Additional cable
8. Engine temperature sensor with cable
9. Interior temperature sensor with cable
10. Cable with three-color LED status indicator
11. Cable with “VALET” button
12. Additional sensor connector with wire…………………
13. Limit switch
14. Limit switch wire
15. Self-tapping screw 4.2x13
16. Plastic tie 120 - 150 mm
17. Ground contact
18. 5-pin autostart relay module
19. Connection diagram...
20. Programming Guide………………………………………………………
21. Installation manual
22. Operation manual
23. Plastic card with an individual PIN code………
24. Packaging
– – –
Replacing the battery in the key fob The LCD display of the key fob has an indication of low battery. The battery must be replaced if the key fob does not turn on or the discharge indicator starts flashing.
In addition, the need to replace the battery will be indicated by the key fob switching to an economical audio confirmation mode. Instead of playing melodies, the key fob will emit short single-tone signals. In this case, notification of alarming events will sound as usual - with a multi-tone loud signal, but without turning on the vibration detector.
To replace the battery:
Slide the battery cover in the direction indicated by the arrow;
Remove the battery from the battery compartment and install a new one;
The key fob is ready for use (turn it on by pressing the button for three seconds).
ATTENTION!!! Also, the need to replace the battery is indicated by the constantly working vibration detector of the key fob. If the key fob constantly vibrates, it means the battery charge is insufficient to continue normal operation. Replace the battery immediately!
ATTENTION!!! The operating time of the key fob before replacing the battery depends on the quality of the battery. The best capacity indicators are provided by AAA DURACELL and ENERGIZER elements. When purchasing a new battery, pay attention to the production date and expiration date. Low-quality elements from little-known companies, expired batteries, batteries with improper storage temperature conditions (unfortunately, a common occurrence) may have many times less residual capacity. The nominal capacity of the AAA element is no worse than 1000 mAh. With such a capacity, the element ensures the operation of the Pandora DXL key fob in real use for at least 6 months.
– – –
"Turning on the key fob"
"Turning off the key fob"
"Loss of connection"
"Attention"
"Anxiety"
"Arming"
"Disarming"
"Malfunction"
“Engine stop in 1 minute.”
"Engine stopped"
"Engine starting"
Purpose of the light indicators of the key fob The use of flashing indicators has made it possible to increase the information content of the key fob in insufficient lighting and an unfavorable noise environment that does not allow it to respond to the sound signal.
– – –
Flashes - confirmation of communication in the notification channel (with the ignition off) "Alarm" indicator (Red) Flashes frequently - confirmation of receipt of the notification by the key fob Flashes Communication with the main unit is lost, or an alarm message is received q After the end of any alarm notification, until until any button is pressed, it flashes briefly and additionally, once a minute, three short sound signals are heard (unless the sound signals are disabled by the “MUTE” function). It starts flashing 3 minutes after the system is disarmed; transition to this q mode is accompanied by a sound signal “Loss of connection”
Key fob functions Turn on and off the security mode using different buttons.
q Monitoring the status of 11 independent security zones.
q Vibration alert built into the key fob.
q 16 sound alert melodies.
q Automatic fluorescent backlight of the LCD display.
q Confirmation of long button presses with a vibration signal.
q Indication of the degree of battery discharge, warning of the need to replace q batteries.
Indication of the current time, alarm clock.
q Display of engine temperature or interior temperature.
q Battery voltage indication.
q The ability to quickly remotely adjust the sensitivity q of warning and alarm levels of the built-in shock sensor.
The ability to quickly remotely adjust the sensitivity of the built-in q motion sensor.
Convenient algorithm for selecting functions based on active icons on the display.
q Communication range with the processor unit is over 1800 m in line of sight.
– – –
Automatic control of the radio coverage area of the notification channel q Indication of actions performed from another key fob registered in the system q Increased service life of the AAA battery.
q Preparing the key fob for operation At the time of delivery, the key fob is completely ready for operation. To turn on the key fob, press the button and hold it for 3 seconds. (until the 3rd beep). The melody “Turning on the key fob” will sound and an indication will appear on the display. Press and hold the button again for 3 seconds. turns off the key fob, the melody “Turn off the key fob” will sound.
In order to reduce the energy consumption of the key fob, the indication on the display automatically turns off after 5 minutes. after the last press of the key fob button (or receiving a message from the system). An alarm event or pressing any button will cause an instant transition to full-function mode.
General information To facilitate the perception of events, the key fob uses 16 melodies. Each melody corresponds to a separate event. The volume of the melodies varies; for service events it is lower, for alarming events the volume is maximum.
The use of flashing indicators has made it possible to increase the information content of the key fob in insufficient lighting and unfavorable noise conditions that do not allow responding to the sound signal.
12/53 manuals.alarmtrade.ru ATTENTION!!! Because All control commands are transmitted via a radio channel, then when working with a key fob, in order to achieve maximum efficiency and maximum radio communication range, it is recommended not to cover the built-in antenna area with your fingers (see figure) Silent operation mode of the key fob In this mode, all sound signals of the key fob are turned off, except for the alarm ( preliminary sensor levels are indicated silently) and alarm signals, light and vibration alarms are turned on.
Control: By successively pressing the button, place the cursor on the icon. When you press the button, silent mode will be turned on, and when you press the button, the mode will be turned off. The icon flashes during the entire time the silent mode is turned on.
Setting the clock and alarm key fob
1. Setting the clock
2. Setting the alarm clock ATTENTION: while setting the clock and alarm clock, it is impossible to arm or disarm by long pressing the and buttons.
Setting the clock By successively pressing the button, select the clock icon. At the same time, all 13/53 manuals.alarmtrade.ru clock numbers will begin to blink. By short pressing the or buttons, set the required value of the current time: hours - with the button and minutes - with the button.
Long presses on the buttons lead to a quick selection of values.
To go to setting the alarm, briefly press the button; to exit the programming mode, press and hold the button for 1 second, or exit automatically after 10 seconds.
Setting an alarm Short press the button to select the bell image, it will start flashing. or will appear at the hour position. By short pressing the or buttons, set the required alarm state: (turn on) or (turn off) respectively. The transition to setting the alarm time is carried out by briefly pressing the button, all the clock digits and the bell will start flashing.
Set the time in the same way as when setting the clock.
To exit the programming mode, press for 1 second, or exit automatically after 10 seconds.
When the alarm is turned on, the icon lights up continuously on the display. When the alarm goes off within a minute, a short alarm signal (double beep) sounds every 2 seconds and the icon flashes. To turn off the signal early, you need to briefly press any button on the key fob.
Checking the number of key fobs registered in the system
This security system has a command channel with a dialog structure of the code transmitted at high speed and the generation of riddles by a random number generator, which completely eliminates the interception and selection of the code by attackers.
The only possibility of intercepting control is the possibility of adding an additional key fob to the system by an attacker. This is possible when transferring the car for temporary use or for maintenance along with the key fob. If you do not transfer the key fob, but use the “Vehicle Maintenance Mode” as recommended, then it will be impossible to record other key fobs. If the key fobs have been added, then the remaining key fob in your possession will no longer control the system and you will be able to file a claim with potential attackers or car service managers, after which you can register only your key fobs in the system (all key fobs registered in the system must be recorded during one programming session, since a change occurs and learning a new encryption key).
14/53 manuals.alarmtrade.ru You can check the number of key fobs registered in the system by removing and putting back the battery terminal, while the system will notify by the number of siren sounds how many key fobs are registered. You can also check the number of key fobs by the number of orange flashes of the status indicator each time the ignition is turned on when the security is turned off. Periodically check the number of registered key fobs to be completely sure of the anti-theft resistance of the system.
Purpose of icons on the display Security zone icons Information icons
– – –
Hood sensor activation indicator.
If an event triggers an alarm, the icon flashes. Trunk sensor activation indicator.
If an event triggers an alarm, the icon flashes. Door sensor activation indicator.
If an event triggers an alarm, the icon blinks. Motion sensor indicator, the icon blinks when a tilt or movement of the vehicle is detected. Icon for enabling the “motion sensor sensitivity setting” mode.
– – –
Indicator of the "Auto-arming" mode Flashing - the system is preparing to arm Lit - the system is automatically armed The digital display is used to display the current time, alarm time, engine start time, engine temperature, interior temperature, engine start temperature, engine stop temperature , indication of names of automatic engine start modes, on-board network voltage.
Driver call indicator. The icon flashes if the button located on the RF module was pressed in the car.
The indication stops only after pressing any button on the key fob. Pictograms for indicating, setting and controlling the system.
– – –
Indicator for monitoring communication with the base unit. The pictogram lights up when the key fob is connected to the base unit.
Icon for enabling the functions “System status monitoring”, “Viewing event history”
– – –
Indicator for turning on the “maintenance mode”.
The icon lights up during the entire duration of the mode. Functions quickly called by the buttons.
– – –
Opening the trunk lock To open the trunk, regardless of whether the system is armed or not, you must press and hold the button for 1 second. If the system is armed, then simultaneously with the opening of the trunk lock, the trunk zone is excluded from the security circuit and the shock sensor is turned off, all other zones remain protected. If within 15 sec. after receiving a command to open the trunk, you have not opened the trunk, the system will close the locks, protect the trunk area and turn on the shock sensor, notifying you with one flash of the direction indicators.
After remotely unlocking the trunk in security mode, the system emits one siren signal every minute until the trunk is closed. After closing the trunk, the system will close the locks in 15 seconds, protect the trunk area and turn on the shock sensor, notifying you with one flash of the direction indicators. If the trunk is not closed within 2.5 minutes, the system will issue a warning message to the key fob without turning on the siren on the car and will turn on the shock sensor and an additional sensor.
Disarming the system
To disarm the system, you need to briefly press the key fob button, and you will hear two short beeps and see two flashes of the direction indicators if no alarm events occurred during the security period (a long press of the button, more than 1 second, will disarm the system without siren sounds).
The key fob will play the Disarming melody, the security system status icon will take the form corresponding to the current state. If alarming events occurred during the security period, the siren will give out four sound signals and four flashes of the direction indicators, and the key fob, having played the Disarming melody, will play the Attention melody and show the disturbed zones. You can view the history of alarm events in detail using the CHECK key fob command (see “Viewing the event history”).
– – –
To set the system to full security with the ignition off, briefly press the key fob button. In this case, you will hear one short siren signal, and the light indication will confirm the arming function with one flash of the direction indicators (long press, more than 1 second, arming will occur without sound signals from the siren). The key fob will play the “Arming” melody, and the security system status icon will take the form corresponding to the current state. If, when arming, a door, hood or trunk accidentally turns out to be open, or the side lights are turned on (not available on all vehicles), then the car siren will give out four beeps and four flashes of turn indicators instead of one short signal, and the key fob will play the melody Arming arm, will play the Attention melody and show an image of the zone due to which normal arming did not occur.
In this case, the sensor for this zone will be disabled. The sensor will be armed again after 15 seconds. after restoration of its functionality. In addition, when arming, the system ensures that the doors are locked and the engine is blocked.
The system can be installed on vehicles with a delay function for turning off the interior light (programmable function). If the function is enabled, then when arming the system will not respond to the door opening sensor for 15 seconds.
(factory setting, delay value can be changed 0-2 min.). When a zone is armed after a delay, the system key fob will emit two short beeps, indicating the transition to full protection of all zones of the vehicle. If the door is not closed after the delay time has elapsed, the key fob will issue an alarm notification.
The system allows you to use a delay in turning on the shock sensor and additional sensor when arming (the function is programmable). This feature allows you to correctly organize the control of power windows and eliminate false alarms of the shock sensor.
– – –
In this mode, the key fob signals are configured when the key fob leaves the reception area.
Control: By successive button presses, set the cursor to
– – –
flash, and by short pressing the button you can select one of 3 alert mode options:
Turn off notification signals;
Enable audible notification Loss of connection;
Enable notification by Alarm signal To exit the mode and save, briefly press the button, or exit will occur automatically after 10 seconds.
System operation in security mode
2. Motion sensor
24/53 manuals.alarmtrade.ru When an alarm is triggered by one of the alarm events on the car, the siren turns on, the key fob with an LCD display plays the Alarm melody with maximum volume, and the zone that triggered the alarm is displayed on the indicator. Simultaneously with the sound of the sound signal, the vibration detector and a red flashing signal are turned on in the key fob. To turn off the alarm mode, briefly press the or button once. To turn off only the key fob alarm, briefly press the button.
When the warning level of an additional sensor is triggered, the system gives three sound and one light signals; the key fob will play the melody Attention, the icon will blink.
25/53 manuals.alarmtrade.ru In the event of an unfavorable external situation at a car parking site, in which the work of the built-in adaptive means is not enough, the sensors or their levels can be turned off from the key fob with an LCD display.
Alarm Mode Features
If at the moment the alarm was activated, the system was in the security mode with the engine running or the Ignition Support mode, then the engine is blocked, and after the alarm ends, the system goes into full security mode. In other cases, after the alarm ends, the system returns to the previous security mode.
– – –
1. Shock sensor and additional sensor
2. Motion sensor
3. On-board voltage sensor
4. Features of the alarm mode The main task of the system in the security mode is to control the sensors of the zones whose operation is permitted. All alarm events are recorded in the system's non-volatile memory (even if the system's power is immediately turned off) with a record of the exact time of the event. This allows you to display the history of events on the car alarm key fob after any time has passed without communication between the base unit and the key fob.
The system records only alarm events in the protocol, ignoring the recording of activation of preliminary sensor levels.
When an alarm is triggered by one of the alarm events on the car, the siren turns on, the key fob with an LCD display plays the Alarm melody with maximum volume, and the zone that triggered the alarm is displayed on the indicator. Simultaneously with the sound of the sound signal, the vibration detector and a red flashing signal are turned on in the key fob. To turn off the alarm mode, briefly press the or button once. To turn off only the key fob alarm, briefly press the button.
If the alarm signal was not accepted by the owner (by pressing any button), the key fob goes into reminder mode, in which three short beeps sound once a minute and the red ALARM flashing indicator flashes every four seconds. In the security mode, if the notification channel signal is stable and there are no alarm events during the security period, the green SEND flashing indicator flashes once every four seconds.
Shock sensor and additional sensor When the shock sensor warning level is triggered, the system emits three sound signals and one light signal; the key fob will play the melody Attention, the icon will blink.
When the alarm zone of the shock sensor is triggered for 30 seconds. Light and sound signals will turn on, the key fob will play the “Alarm” melody, and the icon will flash.
In security mode, the shock sensor monitors changing environmental noise conditions and adjusts its sensitivity from the initially set one, which reduces the number of false alarms.
When the warning level of an additional sensor is triggered, the system gives three sound and one light signals; the keychain will play a melody
– – –
When the alarm zone of the additional sensor is triggered for 30 seconds. Light and sound signals will turn on, the key fob will play the “Alarm” melody, and the icon will flash.
When a warning or alarm level of a shock sensor is triggered three times within a short period of time, the corresponding sensor level can be automatically temporarily disabled, the system will turn on the sensor automatically if the event that caused it to be disabled does not recur.
The sound signals produced by the siren in case of an alarm from the shock sensor and additional sensor can be canceled when programming the system.
In the event of an unfavorable external situation at a car parking site, in which the work of the built-in adaptive means is not enough, the sensors or their levels can be turned off from the key fob with an LCD display.
Motion sensor The system is equipped with a motion sensor, which in security mode monitors the absence of movement of the vehicle in the longitudinal and transverse directions. It will work when you try to lift the side of the car, as happens when using a jack, and it will work during any, even the most delicate, attempt to load the car onto a tow truck. When the motion sensor is triggered, the siren will turn on for 30 seconds, the key fob will play the “Alarm” melody, and the icon will flash.
On-board voltage sensor
The system is equipped with an on-board voltage sensor that constantly monitors the voltage level. The sensor allows the security system to correctly issue notifications when the battery voltage drops, preventing it from being completely discharged by the senseless repeated activation of light and sound alarms. If the power was lost completely (battery disconnection without disarming), the next switch-on will be accompanied by the activation of the alarm mode, and the event will be recorded in the event memory: a critical decrease in supply voltage with an indication of its time, the key fob will play the “Alarm” melody, the icon will flash.
In alarm mode for 30 seconds. Light and sound signals are turned on, as well as the warning system transmitter. At this time, the system will respond slowly to commands transmitted from the key fob, since most of the time the system is busy transmitting an alarm message, and pauses for receiving commands will be minimal.
Alarm Mode Features
28/53 manuals.alarmtrade.ru If, at the moment the alarm was activated, the system was in the security mode with the engine running or the Ignition Support mode, then the engine operation is blocked, and after the alarm ends, the system goes into full security mode. In other cases, after the alarm ends, the system returns to the previous security mode.
Within 2 sec. the system will not respond to the state of the sensors, awaiting a command from the key fob (for example, disarming).
A sensor that caused the system to go into alarm three times in a row will be temporarily disabled. If the shock sensor warning level is triggered three times, the system will temporarily disable the sensor pre-level. The disabled sensor will be armed again after 15 seconds. after restoring its readiness state.
A sensor that has been triggered a total of 9 times will be disabled until the next time it is armed (except for the shock sensor warning level).
Locking/unlocking doors
– – –
The system controls the door locks, locking them when arming and unlocking them when disarming. When disarming and arming, a two-step mode for unlocking/locking doors is provided (programmable function, requires additional connections). The first press of the button will disarm the system and only the driver's door will open, and the second press will open all other doors.
When arming in two-step mode, the first pulse blocks the doors from unlocking them from the outside, and the second pulse from unlocking them from the inside.
There is a mode for automatically locking the doors when you start driving or when you turn on the ignition, and unlocking the doors when you turn off the ignition. 5 seconds after the ignition is turned on, the doors are automatically locked, and after the ignition is turned off, the doors are unlocked immediately (programmable function). If any door is opened after turning on the ignition, automatic locking will not occur - this is necessary to prevent the ignition keys from being locked inside the vehicle.
Doors can be locked and unlocked by force using the key fob without arming when the ignition is on. To do this, with the ignition on, you need to briefly press the button - the doors will close, and pressing the button will open the door locks.
– – –
Automatic arming If this function is enabled, the system will enter the armed mode after 30 seconds. after the ignition is turned off, any door or trunk is opened and then closed. When this mode is turned on, an icon flashes on the LCD key fob display, warning about the possibility of closing the doors. (The function is activated in programming mode, the factory setting is “DISABLED”.)
Automatic re-arming (“Anti-scattering”)
If this function is enabled, then 30 seconds after disabling the security mode, the system will automatically return to the security mode, provided that no door or trunk was opened or the ignition was not turned on. During the countdown period of this time, the system status indicator lights up red, and the icon flashes on the LCD key fob display. (The function is activated in programming mode, the factory setting is “DISABLED”.)
Delayed arming (“Hands Full”)
The system allows you to use the delayed arming mode if, when leaving the car, it is inconvenient to press the button on the key fob to arm it (for example, your hands are full of things). To activate the mode, with the ignition off, briefly press the buttons and together, the siren will notify with one short signal that the mode has been activated, and the direction indicators will flash once. A long press of this button combination (1 second) will enable silent mode. At the same time, the inscription on the key fob display will flash, and the status LED indicator will glow continuously red. After 30 seconds, the system will lock the doors and arm, a short siren will sound and the direction indicators will flash once. On the 31/53 manuals.alarmtrade.ru display of the key fob with an LCD display, the status icon will take the form corresponding to the system state. To cancel the delayed arming mode that is turned on, just press the System status monitoring button. This function is designed to receive information from the base unit about the temperature of the engine, interior, etc.
Control: By successively pressing the button, place the cursor on the icon, briefly pressing the button will request information about the state of the system within 10 seconds. The indicator will alternately show the cabin temperature, engine temperature and battery voltage.
To exit the mode, briefly press the button or exit will occur automatically after 10 seconds.
To view the event history, briefly press the button.
Viewing the event history To view the history of events stored in the key fob's memory, press the button successively to place the cursor on the icon, then briefly press the button. By short pressing the (forward) and (back) buttons, you can 32/53 manuals.alarmtrade.ru view each of the last 10 events in turn. When an event is displayed, the indicator displays the time the event occurred and flashing icons corresponding to the event. To exit the mode, briefly press the button or exit will occur automatically after 60 seconds. The mode will exit automatically if the key fob receives a new notification about an event on the car.
Remote control of sensors
1. Setting the shock sensor control mode
2. Setting the control mode of the two-zone additional sensor
3. Setting the sensitivity of the shock sensor
4. Setting the sensitivity of the motion sensor Setting the shock sensor control mode This function provides the ability, if necessary, to disable the warning or alarm level of the shock sensor.
By successive presses of the button, select the icon, by short presses of the button, select the desired shock sensor control mode and briefly press the button to save the settings in the base unit.
Setting the control mode of a two-zone additional sensor This function provides the ability, if necessary, to disable the warning or alarm level of an additional sensor.
– – –
By pressing the button, select the desired shock sensor control mode and briefly press the button to save the settings in the base unit.
Setting the sensitivity of the shock sensor This function is designed to adjust the sensitivity of the built-in shock sensor.
To enter the setting mode, by successive pressing the button, select the icon, press and hold the button for 3 seconds. The icon and the left side of the digital indicator will begin to blink, indicating that the alarm level of the shock sensor is currently being adjusted. Short presses of the button increase the sensitivity of the alarm level (i.e. the sensor will be triggered with less impact on the car), short presses of the button decrease the sensitivity of the alarm level of the shock sensor.
The sensitivity of the warning level is adjusted in the same way. A short press of the button switches between the sensitivity settings of the alarm and warning levels.
The maximum sensitivity value of the warning and alarm levels of the shock sensor is “50”.
The current alarm level sensitivity value is displayed on the left side of the digital indicator of the key fob, the warning level sensitivity value is displayed on the right side of the digital indicator.
To send new shock sensor sensitivity values to the base unit and exit the sensitivity setting mode, you must press and hold the button for 1 second.
If within 10 sec. no adjustment actions were performed, the sensitivity adjustment mode will automatically turn off without saving the settings in the base unit.
– – –
This function is designed to adjust the sensitivity of the built-in three-axis motion sensor.
To enter the setting mode, by successive pressing the button, select the icon, press and hold the button for 3 seconds. The icon and the left side of the digital indicator will begin to blink, indicating that the motion sensor is currently being configured. Short presses of the button increase the sensitivity (i.e. the sensor will be triggered with less impact on the car), short presses of the button decrease the sensitivity of the sensor.
The maximum sensitivity value of the motion sensor is “50”.
To send new sensitivity values of the motion sensor to the base unit and exit the sensitivity setting mode, you must press and hold the button for 1 second.
If within 10 sec. no adjustment actions were performed, the sensitivity adjustment mode will automatically turn off without saving the settings in the base unit.
Searching for a car If the system is in security mode, you can make it easier to find your car 35/53 manuals.alarmtrade.ru in a large parking lot by turning on the search mode by briefly pressing the button. The system will cause the siren to sound once and the direction indicators to flash five times, long press will cause the direction indicators to flash five times silently.
Panic mode
The “Panic” mode is necessary if you or your car are threatened, and you need to attract the attention of others to your car. To enable this mode, you must press the and buttons together. The siren starts to sound continuously and the direction indicators flash for 30 seconds. To turn off the mode, just briefly press the or button.
Timer channels
1. Control of timer channels from a key fob The Pandora DXL system has 12 independent timer channels. The operation of timer channels can be tied to events (disarming, arming, alarm, etc.) or controlled from a key fob. Four channels can be controlled from the key fob. Timer channels can be used to control various vehicle actuators or to organize additional engine blocking. When programming the system, you can choose one of the following uses for them, for example:
Unlocking the trunk – activating the electric trunk release;
Two-stage door opening;
Ignition support function;
– – –
Control of additional blocking relays;
Control of code blocking relays;
Turning on the low beam headlights when arming;
Turning on the power window control module when arming;
Turning on the interior lighting when disarming;
Turn on/off external devices from the key fob;
Enabling the engine starting module and much more.
The logic for turning channels on and off, the operating algorithm and timing characteristics can be selected from a wide list of built-in programming capabilities, which should satisfy almost any user requests.
Managing timer channels from a key fob To activate a timer channel, select the icon by successive button presses, and select the required icon by pressing the button
– – –
send a command with a short press of a button.
Quick access to the timer channel CH1 (factory settings for unlocking the trunk) is carried out by pressing the button for 1 second. Quick access to timer channel No. 2 is achieved by pressing the button for 2 seconds.
Indication: icon / lights up while the timer channel is on.
Calling the driver The system provides the ability to send a call signal to the key fob with an LCD display from inside the car. To do this, you need to press the call button on the RF module. The key fob will play the “Call” melody, an icon will appear on the display. To turn off the indication, briefly press the button 37/53 manuals.alarmtrade.ru Maintenance mode (TO) It is recommended to switch the system to maintenance mode when taking the car to a repair shop. When switching to this mode, the security system stops interfering with the operation of standard electrical equipment; all its functions are disabled so as not to create difficulties during maintenance. In addition, when using this mode, leaving the car for maintenance, you do not need to leave the key fob for the security system. In this system, it is impossible to remove the car alarm from maintenance mode without the standard key fob. This is done to prevent the registration of additional key fobs without the knowledge of the owner during maintenance for criminal purposes.
Turning on/off the maintenance mode can be done in the following way (in this case, the system must be disarmed and the ignition is on).
By pressing the button on the key fob with the LCD display, select the icon and press the button to turn on the mode or press the button to turn off the mode.
A sign that the maintenance mode is operating is the status indicator glowing green when the ignition is turned on. Exiting the maintenance mode can also be done by touching the contactor with the iButton key (if the key is registered in the system and the contactor is installed)
Arming with the key in the ignition
The system provides the ability to activate the security mode when the engine is running (with the key in the ignition). To do this, with the engine running, briefly press the buttons and together, the siren will notify you with one short signal that the mode has been turned on, and the direction indicators will flash once. A long press of this button combination (1 second) will enable silent mode. In this mode, the shock sensor is disabled.
– – –
Emergency system management 39/53 manuals.alarmtrade.ru
1. Emergency disarming
2. Emergency arming In case of loss or failure of key fobs that control the alarm, arming and disarming can be done using the VALET button. To disable the system's security mode, you must enter the PIN code printed on the card included in the Pandora DXL kit. The individual PIN code consists of 4 digits and is located under the protective layer.
Emergency disarming
To disarm the system you must:
1. Enter the first digit of the PIN code by pressing the “VALET” button (pause between presses no more than 1 second). The system will confirm the entry of the first digit with a red flash of the indicator;
2. Enter the second, third and fourth digits of the PIN code in the same way
3. The system will confirm the correct code entry with red and green flashes of the indicator and disarm.
If the code is entered incorrectly, this will be indicated by a long red flash of the indicator, and the system will return to the previous state. A new entry can be made only after 5 seconds. Note: to enter the number “0”, the “VALET” button must be pressed 10 times. ATTENTION! If the system has been disarmed and the ignition is turned off, then after correctly entering the individual PIN code, the system will enter the settings programming mode (for more details, see the car alarm programming manual).
Emergency arming To emergency arm the arm with the ignition off, press and hold the VALET button for at least 3 seconds. After 30 sec. the car will be taken under guard. During the countdown period, the system status indicator lights up red.
– – –
1. Immobilizer 0 sec.
2. Immobilizer 25 sec.
3. Code immobilizer The built-in immobilizer function can operate in two modes (0 sec. and 25 sec.) and can be controlled either by an additional press of the key fob button or an additional iButton key (not included). The iButton key must touch a special contactor mounted in the vehicle to deactivate the immobilizer. If deactivation of the immobilizer is assigned to the iButton key, then pressing the key fob button will not deactivate the immobilizer.
Immobilizer function 0 sec. serves for additional anti-theft engine blocking. In this case, after disarming the system, you must press the button again so that the immobilizer allows you to start the engine (or touch the contactor with the iButton key).
Immobilizer function 25 sec. serves to prevent attempts to steal from a short-term parking place (at a gas station or at a roadside store), where it is not customary to arm/disarm the car. If within 25 sec. After disarming, opening the door or trunk, the ignition is not turned on, the system automatically blocks the engine from starting.
After the lock is turned on, the status indicator glows orange when the ignition is off and red when it is on. To exit the immobilizer mode, you need to press the key fob button (or touch the contactor with the iButton key), the status indicator will flash red and green alternately, and the lock will be disabled.
In immobilizer mode, all built-in, additional and code relays connected to the system are turned on. The function is programmable (Factory default mode: Off).
Code immobilizer Code immobilizer is a built-in function that allows you to disarm the system or control timer channels after disarming using a standard vehicle control element (button, lever or pedal). The possibility of using one or another standard control element depends on the make and model of the car.
To enter the “Immobilizer Code,” you must press the programmed button (lever or pedal) a number of times equal to the first digit, pauses between button presses should not exceed 1 second, pauses more than 1 second. are perceived by the system as the end of entering a digit and the transition to entering the next digit of the “Immobilizer Code” (“Immobilizer Code” can consist of a maximum of 4 digits from 1 to 9) After the immobilizer is entered correctly, the system will either be disarmed (similar to 41/53 manuals.alarmtrade.ru master PIN code), or the programmed timer channel is activated. Which may be responsible for the operation of the engine and thereby performing blocking.
The assignment of a standard button (lever or pedal) and programming of the “Immobilizer Code” is carried out programmatically (see sublevels IV-6, 7.1).
HANDS-FREE mode
When the Pandora DXL3210 car alarm and the Pandect IS-471/477/577/590/600 immobilizer work together, it is possible to implement the HANDS FREE function, i.e. arming and disarming a vehicle without using a key fob. The car owner does not need to take any action to disable the alarm system and deactivate the anti-theft function, just bring the immobilizer key fob to the car. In the coverage area of the radio channel, an interactive high-speed exchange of authorization codes is carried out in the 2.4 GHz frequency range between the key fob and the engine blocking module, a disarming command is sent to the base alarm unit, and the immobilizer blocking is disabled.
When the HANDS FREE function is enabled, disarming occurs when the immobilizer key fob appears in the radio coverage area. Arming is carried out in the absence of a key fob tag in the radio coverage area for more than 10 seconds.
The system provides the ability to disable the security mode using this function only if the additional warning zone is violated. sensor (see programming manual).
Note: when opening the trunk in security mode from the key fob, the “HANDS FREE” function will not disable the security mode.
To select one of the options for operating the HANDS FREE mode, you must select the icon by successively pressing the button. Next, press the button and hold for 3 seconds, the icon will start flashing.
By short pressing the button, you can select one of 3 mode operation options:
HANDS FREE mode is disabled Disarming is allowed using the HANDS FREE mode Arming and disarming is allowed using the HANDS FREE mode To save the settings, briefly press the button and the settings will be
– – –
To exit the mode without saving the settings, briefly press the button, or the exit will occur automatically after 10 seconds.
The function is programmable (Factory setting of the HANDS FREE mode is off) “ANTI-HI-JACK” mode
1. Passive mode
2. Active mode Anti-Hi-Jack mode provides the ability to prevent attempts to seize a vehicle by force. It provides for the possibility of gradually blocking the car engine while driving.
There are two types of mode – “Active” and “Passive”. Passive mode is used if you are driving and a passenger is trying to take control of your vehicle. In this situation, you need to press the required button on the key fob and, having made sure from the signals of the status indicator that the Anti-Hi-Jack mode has turned on, leave the car at the slightest opportunity. The active mode is used if the seizure has already occurred, you are outside the car in the range of the key fob and the key fob remains with you.
In any case, the Anti-Hi-Jack mode will allow the thief to drive away to a safe distance for you, after which the security system will turn on the light and sound alarm and block the engine. It will take the attacker considerable time to unlock the system.
ATTENTION!!! The Anti-Hi-Jack mode is not a standard mode of the security system, as it involves a complete stop of the engine while the vehicle is moving and can lead to an accident. We strongly do not recommend using this mode. Responsibility for using this mode rests entirely with the owner of the vehicle. For some types of cars with an automatic transmission, the use of this mode is not recommended, as it may damage it.
Passive mode
Stage 1 (ready mode). The ignition must be turned on, the doors must be closed, and when receiving a threat from a passenger, discreetly press and hold the buttons and key fob for at least 1 second. The ready mode will turn on, the indicator will produce single short green flashes, and the icon will light up on the key fob display.
43/53 manuals.alarmtrade.ru Stage 2 (countdown). If the driver is forced out of the car, opening any door and then closing all doors starts a 30 second countdown. Time is given for the car to move to a safe distance for the owner. During this time, the indicator flashes green continuously.
Stage 3 (blocking warning). After the 30 sec countdown time has elapsed. The warning signal of the siren and light alarm is turned on to avoid an emergency situation on the road. The car at this stage attracts attention and warns that the engine will be immediately blocked.
Stage 4 (engine blocking and alarm mode). The engine lock is activated, as well as for 30 seconds. The siren signal and light alarm are activated.
Stage 5 (security mode with ignoring key fob commands). The system will go into security mode, but control via key fobs will be temporarily disabled.
NOTE: At stage 1, you can turn off the “Anti-Hi-Jack” mode by pressing and holding the key fob button for at least 1 second, while all doors must be closed. In other cases, disabling this mode is possible only using the “Emergency disarming” procedure.
Active mode
Stage 1 (countdown). If the owner has already been forced to get out of the car, you must press and hold the buttons and the key fob simultaneously for at least 1 second. A 30-second countdown starts, which allows the car to move to a safe distance for the owner. During this time, the indicator produces single green flashes, and the icon on the key fob display begins to blink.
Stage 2 (blocking warning). After the countdown time has expired, for 30 seconds. The warning signal of the siren and light alarm is turned on to avoid an emergency situation on the road. The car at this stage attracts attention and warns that the engine will soon be blocked.
Stage 3 (engine blocking and alarm mode). The engine lock is activated, as well as for 30 seconds. siren signal and light alarm.
Stage 4 (security mode with ignoring key fob commands). The system will go into security mode, but control via key fobs will be temporarily disabled.
NOTE: Disabling this mode is only possible using the “Emergency disarming” procedure.
44/53 manuals.alarmtrade.ru For security purposes, it is NOT RECOMMENDED to keep the alarm key fob and car keys on the same bunch.
When the system is delivered, Anti-Hi-Jack mode is disabled in the software settings.
To use it, you must set the corresponding programmable settings level setting to ENABLED.
Automatic and remote engine control Remote and automatic engine start, general information The Pandora DXL 3500 system allows you to remotely start the engine by command from the Remote Engine Start key fob or automatically start the engine using the pre-configured Automatic Engine Start function. Starting procedures are used to warm up the engine and interior of the vehicle, charge the battery, prepare the vehicle for intense driving, or to cool the interior of the vehicle with air conditioning.
Remote and automatic engine starting is possible only when the system is in security mode.
If the car is equipped with a manual transmission (manual transmission), then remote or automatic starting will occur only if the preparatory procedure Program Neutral was carried out before arming the car, to prevent the possibility of starting the engine while the gear is engaged and unauthorized movement of the car.
Remote and automatic engine starting on vehicles with an automatic transmission (automatic transmission) will only occur if the selector lever is in position P and the handbrake is applied.
When using the remote and automatic engine start modes, it is worth paying special attention to the reliability of fixing the car in the parking place with a hand brake or other means that limit possible movements of the car associated with vibrations of the running engine. Choose a place to park the car so that it is not on an inclined plane or the slope is insignificant.
The system, being in the remote and automatic engine start modes, continues to perform the functions of protecting all protected zones and sensors, turning off only the shock sensor. The motion sensor in this mode, on the contrary, is switched to a mode of increased sensitivity with a decrease in reaction time to movement. If, while in these modes, the system detects a violation of protected zones 45/53 manuals.alarmtrade.ru (opening doors, hood, trunk, pressing the brake pedal, turning off the handbrake) or triggering a motion sensor, the engine will be immediately turned off and the system will switch into alarm mode. In this case, all engine locks will be activated.
The system, being in remote and automatic engine start modes, monitors engine operation in order to prevent damage to it according to the following parameters: oil pressure in the engine lubrication system; serviceability of the generator and availability of battery charging current; permissible engine crankshaft speed; permissible engine temperature (when installing an additional temperature sensor). If the parameters do not comply with the acceptable values, the system will immediately stop the engine and send a Malfunction notification to the system key fob.
One minute before the normal engine stop, a notification about this event will be sent to the key fob. The icon on the key fob will flash and once every 10 seconds. The melody will sound Engine stop in 1 minute.
Attention!!!
1. If the system is in remote or automatic start mode, or engine operation is supported by the “Turbo timer” or “Ignition support” modes, then to stop the engine, you must press and hold the button for at least 2 seconds. The engine will be stopped, which will be confirmed by the sound signal “Engine stopped” and the icon going out. A few seconds after stopping the engine, the shock sensor will be armed.
2. To disarm the system (in the mode of remote, automatic start, ignition support) and start driving, you must briefly press the button, the engine will run for no more than 1 minute, during this time insert the key into the ignition switch, turn it to position "IGN".
If, after a remote or automatic engine start, you re-send the engine start command from the key fob, the engine operating time will be increased by 5 minutes. This procedure can be performed many times.
Procedure "Software Neutral"
To avoid emergency situations when using remote and automatic engine start modes on vehicles with a manual transmission, a special preparatory procedure “Program Neutral” is provided.
If you plan to use remote or automatic engine start on a car with a manual transmission, then before arming the car 46/53 manuals.alarmtrade.ru you must perform the following sequence of actions:
1. Without turning off the ignition, with the engine running, securely secure the car with the handbrake. Choose a place to park the car so that it is not on an inclined plane or the slope is insignificant. Make sure that the car's wheels are not in a state of unstable equilibrium, which could lead to spontaneous movement of the car when the engine vibrates.
2. Press and hold the button for 3 seconds (three short beeps from the key fob), when the button is released, the car siren will emit a single beep, confirming that the command has been completed.
3. Turn the ignition key to the OFF position (the engine should continue to run) and remove it from the lock.
4. Leave the car with the engine running and close the doors.
5. Within 1 minute, press the button briefly (with a confirmation siren signal) or long for 1 second. (silent) to set the system to security mode and lock the doors. The key fob display will show the rotation of the fan and indicate the security mode.
6. After 3 sec. the engine will be stopped and the system will go into normal security mode with all sensors, being ready to execute remote start commands or engine autostart functions.
If sublevel II-3.8 “Automatic activation of program neutral” is enabled, then the “Program neutral” procedure will be automatically performed when the handbrake is raised. Failure to comply with the “Program Neutral” procedure entails the system’s refusal to execute commands for remote and automatic engine start.
47/53 manuals.alarmtrade.ru Remote engine start To remotely start the engine, provided the system is ready to start, you must press and hold the button for three seconds (three short beeps from the key fob). A sound signal will confirm the receipt of the command, a crossed out shock sensor icon and a flashing fan icon will appear on the display, indicating that the engine is being prepared to start. After a few seconds, the engine will start, which will be indicated by the “Engine Start” sound signal and the rotating
– – –
The duration of engine operation is set either by the warm-up time or the shutdown temperature.
The maximum duration of engine operation is limited by software to 30 – 60 minutes. (set in the system programming menu).
To stop the engine in warm-up mode remotely, you must press and hold the key fob button for two or more seconds. The engine will be stopped immediately, which will be confirmed by the “Engine Stopped” sound signal and the fan icon going out.
One minute before the normal engine stop, a notification about this event will be sent to the key fob. The icon on the key fob will flash and once every 10 seconds. The melody “Engine stop in 1 minute” will sound.
In this case, you can send a command to extend engine operation:
If while the melody is playing “engine stop in 1 minute.” send a command to start the engine from the key fob, the engine operating time will be increased by 5 minutes. This procedure can be performed many times.
– – –
The Pandora DXL system allows the owner to set automatic engine start and stop modes to warm up the engine and vehicle interior, charge the battery, prepare the vehicle for intense driving, or to cool the vehicle interior with air conditioning. The synchronized real-time clock of the key fob and the base unit of the system, and other autonomous system settings make it possible to implement many conditions for starting and operating the engine, regardless of whether the key fob is in the operational zone of the command radio channel or not.
Programming of automatic start modes and engine operating conditions is carried out on a key fob with an LCD display. To program these modes, you need to quickly press the button to select the icon, press the button and go to the automatic start function menu. The menu has eight sublevels, which can be moved between by pressing a button.
Changing the sublevel value is done using the and buttons.
When changing the values of functions for their execution by the system, before exiting the menu, you must save their value; to do this, press the button to go to the “Send” sublevel and press the button to save or the button to cancel the changes made. The results of the changes will be transmitted to the base unit of the system, which will be confirmed by a short double beep from the key fob.
NOTE: If you do not press the or button, the engine operation settings in the remote and automatic engine start modes will remain the same.
– – –
To exit the engine operation setup mode at any time, press and hold the button for 1 second. (or exit will occur automatically after 10 seconds), but all settings changes made will not be saved.
Automatic engine start at a set time (daily timer) The mode allows you to start the engine at a set daily time and will operate if the mode is turned on in the key fob settings (START menu) and the start time is set.
In this case, the launch will be repeated for 5, 7, 14 days or an unlimited number of times (set programmatically in the system programming menu), regardless of the number of security cycles during this time, after which the mode is automatically deactivated.
Automatic engine start based on engine temperature The mode allows you to automatically start the engine based on its temperature and will operate if the mode is turned on in the key fob settings (START menu) and the start temperature is set.
Setting the engine warm-up time with automatic or remote
– – –
The engine warm-up time limit is set in the “START” menu of the key fob within the range of 0 – 60 minutes. It must be borne in mind that if the condition of stopping the engine upon reaching the set temperature is also activated, then the engine will stop if an earlier event occurs. The maximum warm-up time can be limited (Adjustable in the system programming menu. Factory default is 30 minutes).
Ignition support mode
The ignition support function in Pandora DXL allows you to leave the car with the engine running by removing the key from the ignition, having first made sure that the instrument readings are normal and that the car is securely locked by the brakes, and leave the car with the engine running by arming the alarm system. The engine will run for the set time (up to two hours), after which it will automatically stop. When the engine is running, in addition to the integrity of the vehicle's security circuits, including the brake pedal, handbrake, and motion sensor, the engine oil pressure and engine speed will be monitored. If any untoward event occurs, the engine will be immediately stopped before the set time and the owner will receive an engine fault message on the key fob. When the function is running, the system does not control the shock sensor, and the motion sensor is switched to high sensitivity mode.
The function is activated when the ignition is on and the engine is running by pressing and holding the button for 2 seconds. You can turn off the engine in the “Ignition support” mode by holding the button for more than 2 seconds. In this case, the system will remain in security mode, and the key fob will play the “Engine Stopped” melody.
51/53 manuals.alarmtrade.ru In the Pandora DXL system, the “Ignition Support” mode is organized in a standard way using the “Ignition Support and Blocking Relay”. The operating time of the mode is set programmatically in the programming menu (Factory setting 20 minutes).
Additional control elements, indications and notifications VALET button
The system is equipped with a miniature “VALET” button for covert installation, with which you can perform: “Emergency disarming of the system”, “Emergency arming of the system”
Holding an auction on December 26, 2016 for the sale of the right to conclude...” the objective and subjective properties of money, basic and additional (non-market) properties of money in the pre-industrial era are considered. I'll study...”
"Practical lesson
INTRODUCTION
Thank you for purchasing the P Car Security Alarm System andora dXL
35oo - a premium-class security and service device designed for installation on co-
temporary B-C-D-M-S class vehicles equipped with digital data exchange buses
mi (CAN, LIN). P andora dXL 35oo developed and produced in Russia by the Experimental Pri-
Borostroeniya" (Kaluga), which is the copyright holder of the trademark "P andora"(Pandora)
on the territory of the Russian Federation (certificate No. 408051, 408052).
This product is the result of the work of a group of highly qualified Russian engineers.
uneven, with a high degree of elaboration of all components and many unique
engineering and technological solutions. The product is made on a modern element base
using new technological equipment from world leaders, which guarantees
high quality, reliability and stability of technical and user characteristics.
In P andora dXL 35ooall the features of car operation in Russia are taken into account -
wide range of operating temperatures and humidity, increased vibrations, maximum protection
and from incorrect actions of car service personnel, etc. By installing this car alarm
lization, you can count on pleasure from using the system; its reliability,
the highest security and service properties; three years of unconditional manufacturer's warranty;
service support in most cities of Russia and neighboring countries; operational
power in resolving emerging issues related to the operation and installation of the system, ensures
provided by an online support service and a toll-free telephone hotline.
Pandora dXL 35oo has the most crypto-resistant code for authorizing commands with a unique
a local dialogue algorithm and an individual encryption key for each product
nia (at least 128 bits). "Z avod about experimental instrument making » guarantees users of this system
We provide complete protection against electronic hacking throughout the entire life of the product.
In system P andora dXL 35oo provide the most reliable, and at the same time convenient
in operation security capabilities:
– two PIN codes to prevent unauthorized persons from accessing information about
emergency disarming of the vehicle;
– the ability to change the individual encryption key;
– the ability to control the hood lock, pin door locks, etc.
– the ability to connect coded blocking relays with a dynamic code;
– built-in immobilizer controlled by i-Button (TM) keys and Proximity cards;
Ability to work via a code channel with Pandect immobilizers to ensure
control of wireless radio interlock relays, implementation of the “hands free” mode and expanded
real anti-robbery algorithms.
The security system is equipped with a key fob with two-way communication with liquid crystal information
a speaker that displays as close to real time as possible
In modern life, every car enthusiast needs to take care of the safety of his car. For these purposes, the Pandora 3500 car alarm system is perfect, reviews of which encourage you to buy it.
Pandora 3500
What is this model?
This alarm has an accessible interface and high reliability. Since the spring of 2014, an updated alarm configuration has been released with a key fob that has an LCD display and confidently receives and transmits a signal over a distance of over 500m. The special radio channel of the Pandora 3500 alarm, reviews of which are given at the end of the article, allows you to provide protection against scanning and encoding capture. In the simple (basic) configuration of the Pandora 3500 alarm, there is no automatic start function, as well as a satellite GPS receiver.
Contents of delivery
The Pandora 3500 alarm kit includes:
- Main unit
- Keychain
- Additional keychain
- RF module
- Special sensors (react to temperature, shock, tilt)
- Valet button, indicator with wires
- Alarm installation kit
- Card with pin
- Instructions.
Preparation and installation of the Pandora 3500 system
Removing the instrument panel
At the very beginning of the installation, we first need to remove the additional panels that are located in our car (in the cabin), we also remove the facing panel on the left side (which is located near the front windshield), the steering column trim and the air duct panel. If you do not want to remove the above structures, you can place the alarm under sound insulation, in the area of the pedal assembly in the engine compartment of the car. Disconnect the negative terminal on the battery, as well as all system connectors. To install the alarm we need the following tool:
- Scissors
- Screwdriver
- Soldering iron
- Drill.
Installing the Base Unit
Base unit, general view
As a rule, the Pandora DXL 3500 car alarm, reviews of which are presented on the website, is initially installed from the central unit. The base unit is screwed to the rear surface of the engine compartment after removing all the necessary panels. It should be noted that the main (base) alarm unit, like other elements, must be securely attached and located in an unsightly and hard-to-reach place. After all the necessary work on installing the base unit has been completed, the cable (USB) is removed from it. This must be done in order to be able to connect to a PC and program.
Where is the RF module installed?
The RF module is installed in the vehicle interior. From this module a passage is made to the main (base) block, and an LED indicator is also displayed. The RF module is installed on the windshield under the rear view mirror.
Installation of alarm sensors
Installing a Shock Sensor
We attach the sensor that reacts to impacts to the steering column of the car. We install a microphone on the standard mount under the engine. We install a sensor that responds to temperature on the air duct and secure it with a base bolt.
Installation of alarm wiring
We lay the wiring
We install wiring
On the website for installation and instructions for use of Pandora DXL 3500, reviews contain the following recommendations: it is best to use soldering of the wiring, but twisting can also be used. The soldering method is more reliable and allows for better fastening of wires. To solder wiring, lead-tin solder is usually used.
It is imperative to take into account the fact that the material of the conductors must be identical. This will increase the service life of the wiring. In order to avoid the accumulation of condensation at the soldering points, they must be placed above the other wires. The alarm wiring should not be susceptible to temperature effects of vehicle components, friction, and should be placed hidden under the vehicle's upholstery elements. In the car engine compartment, the wiring is placed in special corrugations.
Wiring connection
Typical connection diagram
Next, we need to connect all the alarm elements and connect them to the main (base) unit. The connection of all elements must be carried out strictly in accordance with the instructions, in the order prescribed by the documentation attached to the alarm. All alarm elements must be properly and securely fastened and hidden.
System programming
PC connection
Connecting to a computer via USB
Alarm Pandora 3500, reviews explain to us how to connect the alarm to a computer. To do this, we will use the USB cable that we brought from the main alarm unit. If you have completed all the steps correctly, then when you connect the cable to your computer (laptop), the indicator will blink green.
Entering PIN code
Attention!!! Please note that the interval of pressing the button should be no more than 1 second.
If the interval is greater, then the system perceives this as the end of entering a number. After we have entered the PIN code, the indicator will flash green and red. This means entering alarm programming mode.
Firmware installation
Screenshot of the site with the necessary firmware
To view the current firmware version, you need to open the dxl Loader window. On the website alarmtrade.ru in the service section, in the firmware and instructions section, we can download a new firmware version for our alarm system. To do this, we are looking for firmware for our Pandora DXL 3500 model and downloading the latest version.
Next, in the dxl Loader window, we select the “download” section, then the “firmware download” item. Next, we should select the location on the PC’s hard drive where we downloaded the firmware from the site. Select the firmware with the pld extension and click “download”. During the installation of the firmware, under no circumstances should you press or disconnect anything.
After the firmware has been installed, we need to enter the PIN code.
Setting up the CAN interface
CAN – interface, general view
To configure this interface, we need to select the make and model of our car, in the dxl Loader program - setting up the CAN interface, in the fourth section. After that, click “record”. Next, we need to configure all the necessary sections of the CAN interface.
Saving settings
Saving settings in a separate folder
Important!!! The motorist should take into account the important factor that after changing the original (factory) alarm code, it should be written down in a place convenient for yourself and inaccessible to others. Please note that this PIN code cannot be restored.